Tip:
Highlight text to annotate it
X
Hello everyone. One of the top requests I get is how to build
a strawberry tower. This video will display all the necessary steps to build your own.
The first step is to place a mark on each end of the pipe, then rotate it 180 degrees
and mark the other end. Then snap a line down the entire length of the pipe. You could also
use a straight edge to mark a line, but I find the chalk line to be more accurate and
easier. Turn the pipe over and snap a second line down the opposite side.
Along each chalk line you will place a series of marks. Starting at 2 inches, draw a mark
every 8 inches. This will be the spacing between each pocket in the tower. If you are going
to grow plants that need more root area, set the spaces further apart. I typically replace
the strawberry plants every season. If they grow for more than one season, they can become
root-bound. Starting at the first set of marks, draw a
line from one mark and connect it to the mark on the opposite side. Then turn the pipe 180
degrees and connect the next series of marks. Continue rotating the pipe while connecting
each series of marks. These lines will be used for cutting the slots in the tower.
Along each cut mark, carefully cut through the pipe until you reach the measured mark
you placed at the chalk line. Do not cut through more than half the pipe! Rotate the pipe 180
degrees and cut the next slot. When you are done, each slot should be on the opposite
side of the previous slot. Time for some good gloves. The pipe doesn’t
become flexible until it is well above the boiling temperature of water. Please be careful!
The general area that will be heated will be an arch shape starting at one end of the
slit, up about 8 inches to the back side of the neighboring slit and then back down to
the other end of the slit.
Heating PVC should be done in a well vented area. If you overheat it, it can release some
nasty gases. Please be careful! Continuously move the heat around the arched area. Try
to avoid heating the area below the slit to keep the pipe from bending too much.
After a few minutes, the PVC will become soft. It helps to apply a little extra heat at the
each edge of the slit since this is where the sharpest bend will be.
Push in the PVC so it makes a concave shape in the arched area. You will want to push
it in enough so that it will touch against the back wall, but not create a seal since
the water will need to trickle through that area, but don’t leave too big of a gap so
your growing media will fall through it. When you let go of the pipe, it will usually spring
back a little, leaving a gap around ¼”. I found it to be very helpful to use a few
spring-clamps to hold the tight bends in place while the plastic is cooling. You will want
to hold the shape in place for a couple of minutes while it is cooling.
It takes me about 3 1/2 minutes to completly create each pocket.
When you are done, you will have some nice pockets alternating on each side of your new
tower. As the water flows through the tower, the
surface tension in the water can cause it to flip out of the edge of the slit. To correct
this, I added a collar around each pocket. With some extra pipe, cut some rings about
1 ½” wide. Then remove enough of the ring so when it’s placed over the slit area,
it extends just beyond the slit. Add some silicone adhesive and clamp the ring in place.
Half of the ring should be placed above the slit line. Use clamps to hold it in place
until it cures. If you’re not going to be draining directly
into a sump tank, you’ll need a way to catch the water from your towers. Take a 4” cap
and add a fitting to it. Drill a 7/8” hole and thread it with a ¾” tap. There are
several ways of adding fittings, but I found this to be very cost effective method.
Take a ¾” NPT to barbed fitting and screw it into the tap. If it is screwed in far enough,
it will be higher than the base of the cap. This work well to help any media that as fallen
through from going down the drain and clogging it.
This cross-section shows how the fitting is placed into the cap.
Place the cap on the bottom of the tower. The bottom pocket should not be filled with
anything so you can clean the base cap if necessary.
S hooks. Use a wire or chain to hang it from a strong support.
To connect the tower drains together, you can attach them with tubing and barbed fittings.
I made some stands from scrap 3” pipe to support the bottom of the tower. Then I used
a 1-1/2” pipe with holes drilled in the side to catch the water from each tower. Each
pipe then drained into the main sump tank.
Filling each pocket can be a challenge so I made a tray-type funnel to speed up the
process. Take a section of pipe and do a cut down its length. Heat the entire piece so
it can be flattened, then bend up the edges so it forms a V shape.
I created a cross-cut section so you could see the inside of the tower. Please note that
this sample is done with black ABS so you could see the various surfaces easier. Each
pocket will hold about 5 cups, or 1 liter of growing medium. This is enough space for
most shallow root plants like strawberries or lettuce. For my strawberry plants, they
will usually get water for 10 minutes every hour and a half.
Thank you for watching. Here’s a quick slideshow of my strawberry towers in action!