Tip:
Highlight text to annotate it
X
Hi I'm Eric from Park Tool, and this is the PK-2 Professional Tool Set. A great way to
for a consumer to have a fabulous home set-up, or a great way for a pro to outfit a bench.
All of these tools, over 65 or our professional level tools, all in this one set.
Starting with products to clean your bike - first of all you get a BCB-4.2, which is this
set of four brushes to clean your bike - a lot of different configurations. This is a
CM 5.2, our chain scrubber - a great way to keep your chain clean, which of course prevents
wear and tear on the rest of your drive train. This is a dummy hub, and this - using the quick release
goes right in your rear drop-outs, and the chain rides on there so you can clean your
bike without the rear wheel in there. You can also transport your bike with this in
there. This is a dummy pedal. So you use this in place of a pedal if you want to run through
your gears, make adjustments, clean the drive train etc.
Moving over to generic tools, this is the PAW-12 - a big, heavy duty adjustable wrench.
This is our HMR-4 - a hammer 4 - a really nice hammer with two different ends on it - a steel
side, and a composite side - a little bit softer. Four different screw drivers. Two Phillips
and two flat blade. This is our shop scissors, a great scissors for cutting all sorts of things in the shop.
Needle nose pliers - side cutters - this is our CN-10, our shop level
cable cutter, cuts cable and housing. Moving to the front these are tire boots. These are
great to take a long on a ride in case you get a cut in your side wall, and then you
can patch your tire from the inside, just to make sure that the tube isn't poking through.
And this is our GP-2 pre-glued super patch kit, which is a great emergency patch kit
to get you home. This is the ATD-1. This is an adjustable torque driver, 4 through 6 newton
meters, adjustable in half newton meter increments. All metal internals, shop level tool. It's
gonna last for years, it's not a throw-away torque driver, that's a great tool. This is
a 8mm hex wrench with a nice handle on it, this is mostly used for pedals and cranks.
Moving up here, this is the IR-1. This is the internal cable set, where you use this
to pull cables through frames - internally routed cables, you pull that through frames
with this set. Extremely useful - there's a lot of guess work if you don't have a tool
like this. This is our AWS-1 - world famous three-way Y wrench. You get one of these,
and you also get an AWS-3 which is - 2, 2.5, and 3mm. The AWS is 4, 5, and 6mm. You
also get a complete set of P-Handled wrenches, which is a flat hex on one end and a ball
driver on the other, and a really ergonomically built handle in the middle.
This is an HCW-15. 32 and 36mm - wrench for threaded headsets.
Cone wrenches. These are our shop cone wrenches so you get a set of shop cone wrenches,
then you also get some double - ended cone wrenches,
in case you have a - two wrench flats of the
same size on the same hub so then we give you some extra sizes.
These are small brake and derailleur wrenches. 8, 9, 10, and 11mm.
This is an offset brake wrench,
so you can use this to center brakes - there's a lot of really hard to get to brake
wrench flats that this is a great tool for. These are our TL-6.2. These are steel core
tire levers, so the inside is steel so it's really strong - the outside is a composite
so they glide over painted or anodized rims. Won't scratch your rim, and tire will peel
right off. You can use those for removal and installation.
Three different sized spoke wrenches - these are the three most common sizes of spoke nipples
so we give you three spoke wrenches. This is a set of Torx compatible tools, lots of
Torx fittings on bikes these days. This is a spoke, bearing and cotter gauge,
which is a great way to measure spoke length, bearing size, and on the old bikes, on the
old three-piece they used to put cotters on the three-piece cranks, and this will measure
those as well. This our DAG-2.2. Derailleur hanger alignment gauge. This is a fabulous
tool. A lot of shifting problems are caused by a derailleur hanger that is not aligned
to the drive train - and this tool not only gauges the alignment, but you can use it to
straighten that derailleur hanger back out. Moving down here, this is our CT-3.2, which
is our shop level screw type chain tool. Adjustable to just about any width chain. MLP-1.2, which
is a master link pliers that will install and remove master links in chains. These three
are crank tools. This is an 8mm on one side. 14mm socket on the other, mostly for three-piece
cranks. These two crank pullers are mostly - for three-piece cranks as well. One for the
splined version, and one for the square tapered drive. This is a tool for removing and installing
cassette type bottom brackets. This is a tool for removing and installing Campagnolo lockrings.
And this is the same tool for Shimano size and style lock rings. This is a very common tool.
This is BBT-9, so this is a tool for removing
and installing external bearing bottom brackets. This is our biggest, strongest pedal wrench
PW-4. Ergonomically designed, you can get to just about any position and it is a big,
long, beefy wrench. In the front here this is a - chain checker to see if your chain
is stretched. If it is, it's time for replacement. This is a chainring nut wrench that goes on
the back side of chainring bolt systems - just to hold it while you ah - install or remove
those bolts. And this is our CP-1 cassette pliers, this takes the place of a chain whip.
And this really fast and handy, it fits a wide variety of sprocket sizes - you just
grab on like a pliers and you would use this in conjunction with a locking remover.
Last but not least - at any bench you need a bottle opener, so the BO-2 bottle opener comes with
this set. All of these tools come in this big tool box, and - there's room for more
tools, there's room for more specialty tools if you want to add to this set. But this is
a fabulous set of high end tools - very diverse - a great way to outfit - completely outfit a bench.
So there you have it, that's our PK-2 Professional Tool Kit. Thank you.
For detailed descriptions on any of these tools
check out the product page for the PK-2 Professional Tool Kit at
ParkTool.com.