Tip:
Highlight text to annotate it
X
Innokin iTaste Cool Fire 2 Mod from GD
Welcome to the video where I would like to introduce hand grenades to you.
No, noÖ don¥t worry... This is no suicide attack going on hereÖ.
These are Cool Fire 2, black and khaki versions,
the mods with the possibility to adjust the output power with revolving ring.
These are the mods for 18350 batteries, they are stainless steel,
perfectly colored ñ and we will check them out.
Cool Fire 2.
A standard cardboard box hiding a brief mod manual, a brief clearomizer manual.
First, I would like to mention that this grenade is available in two color versions.
Khaki, really a super army style, and black,
who remembers times of sporting grenade throwing knows that grenades were always black.
So, black or khaki ñ both colors fit the grenade.
I will take the black version and let¥s see what the packing includes.
It includes the mod itself plus iClear 30b, which we will talk about at the end of this video.
This is different from Cool Fire 1 which includes iClear 30b too,
however with a standard, not flexible 510 driptip.
So, this we will talk about later.
Let¥s see what the grenade has to offer now.
510 thread with a flexible center contact which will adjust to your accessories
since not all of them have the same length of their threads.
This contact will adjust to your atomizer.
Removable top cover, EGO thread so you can use EGO threaded atomizers as well.
Material of the mod is stainless steel and with perfect color.
The text says Cool Fire II, INNOKIN.
WellÖ let¥s put the thread cover with necessary air holes back on.
The mod also offers a variable output adjustment, which can be done with this ring,
7W, 8W, 8.5W, 9W, 9.5W, 10.5W, 11W, 12W, and 12.5W.
That¥s it.
So, output variability ranges from 7W-12.5W.
On/off switch is here, the little dot shows what output is set right now.
Let¥s do some measuring.
Weight of the mod without a battery 196.7g,
length 82.17mm,
bottom cover diameter 25.6mm,
upper cover ring diameter 25.5mm,
inside diameter of the cover ring 17mm,
the widest spot diameter almost 40mm.
Now, let¥s focus on functions.
The mod is designed for use with 18350 battery which you put inside this space.
Again, the bottom cover, as we are used from Innokin, is equipped with this quality mechanism.
Put the plus pole inside the mod, screw in, the switch will run the standard electronic test.
We can use batteries with no protection
because this mod has its own protection against a low battery capacity.
The mod can be switched on by a three-click on the heating switch,
electronic runs the test and is ready for vaping.
In my case, the switch has a green light on which means my battery is fully charged.
If the switch has an orange/yellow light on, it means the battery is half empty.
If the light turns red, it means your battery needs to be recharged immediately.
If you don¥t do that, finally the red light flashes several times
and the whole mod switches off and we cannot vape anymore.
According to the producer, the mod is designed for use with atomizer resistances minimum 1ohm,
maximum output is 12.5W, maximum output current 5A.
WellÖ I think that¥s about all what I wanted to say about this mod and now,
we can have a look at iClear 30b.
First, let me just repeat that Cool Fire 1 is delivered with iClear 30b with a standard not flexible mouthpiece,
part of Cool Fire 2 packing is this iClear 30b with a revolving mouthpiece.
Otherwise they are the same, so let¥s have a closer look at iClear 30b.
It¥s really simple: first a bottom base with a 510 thread with the center contact.
You can see the text engraved here: iClear 30b VV/VW
which means the clear is designed for Innokin products with variable voltage and variable wattage.
I-Clear 30b has an exchangeable head which can be exchanged very easily like this.
The head has 2.1ohm resistanceÖ which can be seen hereÖ.
So, this concrete head is meant for a Cool Fire 1 mod which has an output wattage 8.5W.
There are two heating coils, oneÖtwoÖso it is a dual coil system.
The whole head can be easily exchanged like this.
The rest is a quality polycarbon tube and the top base with an airflow pipe.
And a 510 driptip depending on the version 1 or 2 of the Cool Fire mod.
The bases are stainless steel.
This is how you can refill the clear.
Unscrew the bottom base and gently pour the liquid in by the sides,
screw back in the bottom base, and that¥s it.
Now, the clear is ready for vaping, just wait a bit so that the wicks can absorb some liquid first.
Ready and soakedÖthis is a real nice thingÖ.and we can go for itÖ.
It vapes.
I-Clear 30b ñ well done iClear.
There¥s nothing to criticize on this dual coil.
Handling this grenadeÖwellÖ. it just fits your head perfectlyÖ
Its diameter is really pleasant, the weight is not a handicap either.
Really great.
As I said, you can also use EGO threaded accessories.
So, this is how it works with EGO threaded clearomizers.
We will go back to the thing which is designed for this mod.
If you have a clearomizer with a longer threadÖ
Here it is made so that you can really screw it in all the way and it¥s ok.
Sometimes, you will be all the way and still you will not reach the end.
Then you can just move the cove a bit back and then tighten it back against each other.
This will save you problems with central contact sealing.
So, this is a grenade, Cool Fire 2, really an impressive item and design delicacy.
Have a nice time and see you again at some of my future videos.
For Gold Drive made by Vorel Vaping Film¥s.