Tip:
Highlight text to annotate it
X
Versatile modular battery-tank modes (electronic cigarette / hookah) Review, Part 1 of 3. Battery pack.
Good day
Now I want to tell and show
how it works, what it consists of and how is going to
mod SvoeMesto v.2.0
We start in the order - with the battery pack.
The battery compartment is a tube made of chrome-plated brass.
There's also a shorter battery compartment.
Standard battery compartment accommodates a battery 18650.
Output voltage of 3.7 volts.
Or two batteries CR123
The total output voltage of 7.4 volts.
Short battery compartment accommodates a battery CR123 3,7 volts.
To make it work to connect to the battery compartment button.
Buttons can be of two types
this is a normal button
and button with locker.
Now I will tell you what the difference between them and how they work.
Normal button consists of two parts
the body and buttons pusher.
Once assembled, it looks like this.
When you click on
is the closure minus the battery contacts inside the battery compartment.
Let's put this button.
We see that the button has milled grooves.
What are they for?
If the battery inside the battery compartment that something will happen and lose tightness
These holes will serve to divert gas from inside the battery compartment.
To the battery compartment is not turned into a grenade that could explode in their hands.
This protects the battery during depressurization.
How do we collect the?
On the top button and put a spring cranking battery compartment.
On top of the battery compartment so we put a seal.
This gasket is needed to ensure that the spring does not lock on the negative battery contact.
The closure minus the battery, we need to contact the central button, rather than spring.
Insert the battery and cranking the cover.
That's the cover.
The cover is threaded under the 510-th atomizer and it can be screwed or any atomizer or cartomizer with a thread.
That's how we got the most simple mechanical battery pack.
How does it work?
By clicking inside the closure minus the contact occurs and the battery circuit is closed.
Let's see how it works with ordinary cartomizer.
Screw cartomizer.
As you can see - it works fine.
Often the question arises - whether it is convenient to press a button to end?
For me personally - it is convenient.
How to hold a mod that it is comfortable?
Must hold a pen while writing and press a button with the middle finger.
There is no discomfort.
Unscrew the button and see that the button has a small screw.
We can loosen this screw and tighten a little more deeply,
thereby adjusting the depth of the button is pressed.
You can adjust the depth of 0.5 mm pressed
5-6 mm - as someone comfortable.
With this button we can put the mod upright on a horizontal surface.
Pusher button located on the same plane with the body and accidentally pressed the button does not happen - to press the button it should push into the shell.
Now consider a button with the locker.
Its design is more complicated.
It has such detail as the locker.
In the twisted state can lock button to be pressed.
If we unscrewed the locker, it button pusher stall and not give her a push.
The assembly is the same as a normal button.
Button - spring - laying - the battery.
The closure is at the center.
Now cranking battery compartment.
In this position we have open locker and we can not push the button.
In this position, the modes can be placed on a horizontal surface. Accidentally pressed, will not happen.
Unscrew the locker. Now we can press the button.
To press the button we no longer need to dent plunger button in the body of mod - you can just press a finger at him.
Principle of operation - such as in an ordinary button.
The difference is that in the unlocked mode can not be placed on a horizontal surface
press the button under the weight of mod
Do not forget to unscrew the locker.
Now look all the same, but with a conventional battery pack.
With battery 18650.
We will see that everything works the same way.
Button - spring - laying.
Cranking battery compartment.
Insert the battery.
And the cover.
We had a standard mechanical battery pack under the battery 18650.
Similarly, it works fine.
The last item, which can be attributed to the battery pack
variwatt spacer "Semovar."
This spacer the button to the side
the display.
Inside is a circuit board that controls a device.
Cheat this spacer on the battery compartment.
To wind from the top cover from the 510-m connector.
What we have in this case is going on?
We have a button in the end, you want to push the chain to be closed.
And we have a button on the electronic board, which must be pressed, the device worked.
To all worked well, we must have the button in the side mode
possible to unscrew a screw
that it was longer and always rested on the battery.
To button was always pressed.
There is one slight drawback.
This button is a floating contact.
More than a transitional device contacts - all the worse.
Therefore, for use with a special cap VW.
This stub also has openings
for removal of gases during depressurization of the battery.
This one-piece cap and screwed in place of buttons from the end of mod.
Using the plug is not required, but I highly recommend it.
We look VW battery pack.
The device we have already included - can vape.
Here is the mod in comparison with ProVari.
We see that with the standard battery pack mod is slightly longer than ProVari.
Screw the battery compartment instead of the standard short.
Use one battery CR123.
In this case, the size will be smaller.
We see that in this configuration modes have already received is shorter than ProVari.
But we must not forget that the battery CR123 is about 4 times less capacity than 18650.
If you have enough on day one battery 18650, then the CR123 will have 3 or 4 pieces.
We get the savings in size, but will be forced to carry extra batteries.
We continue on. With the battery pack we've finished.
About VW described in detail in other topics on this now I will never stop.
Just proves once again that it works fine.