Tip:
Highlight text to annotate it
X
Welcome to the final instalment in our video tutorial on how to make a carbon fibre bonnet.
In this instalment we're going to be looking at trimming these two outer and inner skins
that we made in the two previous videos, and we'll be fixing the fasteners and bonding
these two skins together and then putting the final touches to our finished component.
First thing to do is trim this inner moulding. To do that we're going to be using a Dremel,
like this, and we're going to be rough trimming around the edge following the original line
of the bonnet and then taking out this inside section as well. Now some obvious points that
we've got to make before we start the trim is safety precautions. We're going to be using
a good quality dust mask, eye protection because we're working with high speed tools, and we've
got our localised extraction that's going to be taking away all of the carbon dust.
Now with that out of the way we can get on with the trim. Now that we've done the rough
trim using the Dremel, the next step is to use a Perma Grit file like this to tidy up
these edges considerably. So we just do that, go all around the edge making this flat and
consistent all the way around. The
next thing we're going to do is drill the holes for the hinge fasteners. To do this
we've marked out the position for the two holes which we've measured off the original
bonnet, and we're just going to use a normal drill bit ensuring that it's quite sharp.
We're going to use a high speed and we're going to use steady pressure. We're going
to put a block underneath to prevent the carbon fibre from bursting as we get through. We've
marked out the area at the front for the catch mechanism and we're just going to cut this
out, again using the Dremel and then use a file to finish the edges. We're looking now
at the fasteners. We're going to be using these special bonding fasteners which are
designed for composites use and we're going to be gluing these in place and that's going
to be the studs for the hinge pick up, and we've also fabricated this keep mechanism
for the latch and we've just keyed this up with the grinder so we've got a good bonding
surface. For bonding the fasteners we're going to be using a structural epoxy adhesive this
is from our Perma Bond range, it's the ET500. Now we're using an epoxy because that offers
excellent bond strength to both the metal and the composite material which is obviously
perfect for bonding fasteners. So apply the adhesive through a static mixer nozzle which
actually mixes the two parts to the epoxy as it goes. And we put plenty of adhesive
all around the area to be bonded. the peel ply finish of course on the underside of this
laminate is ideal for bonding to already. And then we just push the fastener down into
the adhesive and what we're looking for with a boding fastener ideally is for some of the
adhesive to squeeze up through the holes in the bonding fastener and actually out on top
of the fastener creating a mechanical lock to hold that fastener in place. And then the
same again with the latch mechanism just bond that to hold it firmly in place. To bond the
two halves of the bonnet together, we're going to use the upper mould to hold the parts stable
and secure whilst we do the bond itself. So we take the upper skin and drop it back into
the mould that we used to make it in the first place, and then we can take the inside skin.
Now it's only about ten minutes after we've bonded these fasteners but you can see they're
already incredibly secure, no danger of those moving, and so we're actually ready to bond
these two skins together. For this bond we're going to use a different adhesive to the one
that we used for the metal fixings and that's because epoxy adhesives are recommended where
you're bonding between plastic and metal but for a plastic to plastic bond such as this
then the ideal adhesive is a polyurethane. So we're using the Perma Bond PT326 from our
range and we're going to be putting a large bead of the adhesive all the way around the
perimeter, both this edge and the inside edge. So it's a twenty minute adhesive it's not
too much of a panic, again we're using a static mixer nozzle. So the adhesive will be thoroughly
mixed by the time it makes it to the part. It will have some gap filling to do so we
don't want to be too short with the adhesive. We've just got a small amount of spring in
this inner moulding that's holding it off the outer skin so we're just going to pull
some vacuum bagging film over this to protect it and then weight these down with some bricks.
This adhesive is about twenty minutes to tack so we're going to leave this around about
forty to forty five minutes before we come back to it but before we go we'll make sure
that we've got good contact all the way around the edge. Now that the adhesive has cured
we're going to remove the weights and take the part out of the mould. and you can see
here where this excess adhesive has actually spilled over onto the upper moulding and that's
the reason why we didn't trim this upper moulding earlier we've just left this so we can trim
it now and that's prevented any of this excess adhesive from going onto our mould. We're
now onto the final trim. This is of course the most important because when this bonnet
is fitted to a vehicle this is going to be clearly seen. So what we're going to do is
trim it again using a Dremel, and we're going to do that a few millimetres wide of where
we can see that the original bonnet ended, and then we're going to rub the edge back
using a sanding block. After we've finished with the Dremel a Perma Grit block like this
is absolutely fantastic for rubbing back to the line. So we can see clearly where the
bonnet should end and that's just a slightly over run that we've been left with from the
Dremel. And then we just finish these edges by hand using abrasive papers, probably going
for a 120 and then finishing up with a 240. That now concludes this video tutorial. We've
made an extremely light visually perfect carbon fibre vehicle panel, and with the information
that we've given you in this tutorial so can you. So as ever all of the materials, the
supplies and the equipment that you've seen in this video are available from our website
easycomposites.co.uk and if you want to discuss this project we hope to see you on the forum
talkcomposites.com.