Tip:
Highlight text to annotate it
X
With many devotees, pinhole photography is the art of taking photos in a "lensless" fashion;
instead, a pinhole is placed over the usual lens, in order to create soft, "artsy" images.
You can make your own pinhole lens for your SLR (digital or film) from the camera's body
cap, using simple materials and tools. Doing this will even improve the effects on older,
less capable cameras and you'll capture some neat effects on film.
Find the center of the body cap..
Mark a dimple in the center of the body cap with the center punch tool.
Using a nail or similar tool is also effective.
Drill a hole measuring approximately 1/4" / 6.35mm..
Using the center mark that you created in the previous step, drill a hole in the body
cap. Use something under the body cap to protect
your working surface if needed.
Cut a square piece measuring approximately 3/4"x 3/4" / 1.9 centimeter (0.7 in) x 1.9cm
(approximately) from the aluminum sheet..
Using a soda can with the top and bottom cut off, cut a 3/4" (1.9 cm) square to 1" (2.5cm)
square piece. The size does not need to be exact nor exactly square, however the size
must be small enough to fit flush inside the body cap yet large enough to hold while sanding.
Round the corners of the square piece for safety.
Make a dimple in the center of the aluminum piece..
Take a sturdy sharp needle, and slowly use a twisting motion with gentle pressure, to
make a dimple in the center of the aluminum. Go slowly and steadily so as not to create
a hole that is too large.
The dimple should be just visible on the underside of the aluminum piece.
Do not push the needle all the way through; there shouldn't be a visible hole at this
point, only a dimple.
Sand the dimple.. Using very fine grit wet/dry sanding paper
(emery cloth) of 600-800 grain or finer, gently sand the dimple flush with the surface of
the aluminum surface. After the dimple has been sanded away, a small
hole should appear in the aluminum.. Use the needle once more to gently round out
the hole (both sides).
The optimum diameter of the pinhole depends on the distance from the pinhole to the film
surface (digital sensor). For most (D)SLR cameras that is somewhere around 50mm. Using
a pinhole calculator, the optimum pinhole size is apx .3mm. A #13 sewing needle should
pass through a .3mm hole but a #12 needle should not.
The size does not have to be exact at any rate, any hole close to .3mm will work just
fine. If the hole is too small, gently use the needle
again to enlarge the hole and sand both sides smooth.
If the hole is too large, try the lens to see how well it works, or discard the piece
and cut a new one. What is important is to make the hole as round
as possible and to keep the edges smooth and flush with the surface. Jagged edges will
cause diffraction effects and show up on the final image.
After you have sized the pinhole correctly, clean the aluminum piece and the pinhole with
rubbing alcohol and blowing through the pinhole.. Doing this is important since residue can
get in the pinhole and cause image distortions or worse the residue can get on your camera
sensor and require a cleaning. Apply adhesive..
Using a toothpick, or something equivalent, sparingly spread the adhesive around the edge
of the aluminum piece, being careful not to get any adhesive near the pinhole.
Use silicone adhesive as you can easily remove the pinhole from the body cap and remove the
adhesive from the body cap if you ever need or want to.
Carefully place the aluminum piece into the center backside of the body cap..
Make sure to center the pinhole in the drilled hole in the body cap.
Try to be exact when positioning the first time, in order to keep the adhesive from getting
all over the body cap and possibly into the pinhole.
Tape the aluminum piece in place while the adhesive dries..
Do a final check to make sure the pinhole is still centered on the hole in the body
cap. After the adhesive dries, carefully remove
the tape..
Cut a very small square piece of tape and cover the pinhole..
Mask the body cap.. Leave the aluminum piece exposed so it can
be painted black. Spray flat black paint over the aluminum piece..
This will greatly improve the image quality. Remove the small square piece of tape covering
the pinhole..
Using a black permanent marker, dot the remaining aluminum surface so it is black..
The ink sticks better when dotted onto the surface rather than wiped because the aluminum
surface has no tooth for the ink to adhere to.
Be careful not to dot over the pinhole. This area does not have to be perfect as it will
not reflect as much light as the entire aluminum surface would.
Remove all the masking tape and do a final cleaning..
Attach the body cap to the camera body. Put your SLR in manual mode and set the shutter
speed to 2 seconds to start.. Take a photo. Look at the histogram. If the
graph indicates that the image is over-exposed (the histogram will show data bunched to the
extreme right) or under-exposed (histogram data is bunched to the left), adjust the shutter
speed to compensate. Once the exposure is set you can use this
exposure while shooting in similar light conditions.
Depending on how bright the scene is your exposure time may vary from several seconds
to just under a second. The yellow flower photo shown here was exposed for 1/2 a second
at ISO 400 in full sun.
The sun through the leaves photo was exposed for 1/15 of a second at ISO 400.
If your scene lighting changes, recheck the histogram and adjust shutter speed to compensate.
Thank you for watching!