Tip:
Highlight text to annotate it
X
Hello everybody!
Now I'll show here for you
the torch TL26
Also manufactured by the line MASTERTIG
of "Ck Worldwide"
this torch,
It is the torch that every welder would like to have,
Why?
It is a torch very special
The welders who weld in the field mainly
They need a very flexible torch, very malleable,
for him can make the Technical "Walk the Cup"
The welder who uses the technique "Walk the cup"
he needs a torch light "very light"
and very flexible,
that has a very flexible cable, such as you're seeing here,
This torch it is fantastic,
That's what the welder wanted to have there with him.
Look here, for you to see.
I'll show it in detail here now.
For you are knowing,
the dream of all TIG welder.
The conventional torches, which has in the market.
this cable that came with the torch
It is very hard, very rigid.
The welder to do the technique, "Walk the Cup "
he would have to roll up here
To facilitate the movement of "Walk the cup. "
he has great difficulty to do,
Look, as it is hard and rigid,
Look here, the position it is stop, it gets locked here.
it is very rigid, very hard.
See the difference of flexible cable
In comparison,
with the previous, CK26
and the TL26,
Has no comparison!
Guys!
See the flexibility of this cable.
It's impressive how much that is soft
And the most important
This torch so light thus,
so tiny thus
It's 200 amps @ 100%
No other torch on the market, has these characteristics. Ok!
You can buy this torch, making the your order,
It may come with the cable of 12 1/2 feet (3.8 meters)
or 25 feet !7.0 meters), Ok!.
So in the time to order, you choose.
This cable here, it's with 25 feet (7.0 meters)
and as I have a machine "ThermalArc"
It already came with a plug, set up,
for me, put in my "ThermalArc"
If you have a Lincoln, a MILLER, a HOBART,
It also may already to come ready to you,
Otherwise comes only the cable and then you put in your plug there.
of machine that you has there. Ok!
This here is the torch CK26
The torches standardized No. 26
It is the standard HW 26
It is the torch that you normally use there in their work.
I see that some welders when will make the technique "Walk the cup"
They even cut here,
to decrease
this distance here, of the handle
to facilitate its movement, of the wrist at the time making the "walk the cup".
Note that this torch here.
it is shorter.
the TL26,
It is shorter, but
has the same capabilities of this larger
200 Amps @ 100%
This here is the CK17 with valve,
when you weld carbon steel,
You can use this torch with valve.
Do not give too much trouble, if you have some care.
However, it is in the output, the time you will interrupting the welding
is that many times the torch with valve
let the welder in a difficult situation
As you now see in this sequence.
For welding of stainless steel
For exemple,
these materials very sensitive to oxidation.
I can not use a torch with valve.
Where I open the gas here.
and by contact,
I open the arc, but to stop the arc (the electric arc).
I have to abruptly remove the torch.
This in welding stainless steel, is not allowed
Besides oxidize the end of the the weld pool
Can leave that hole in the the end
As you see here in this sequence as well.
On the normal torches you use there, and find on the market.
which are standardized No. 26, regardless of the manufacturer
Many times you use this type of trigger
when you use a machine electronics.
that has an opening of the electric arc, with High frequency.
or by "Lift Arc", by contact,
as I showed in my other videos here.
This type of trigger,
It is a bit uncomfortable
It has these clamps here
that bother a bit at the time of welding
and also, when you press here
If your machine does not have the setting "4T"
You have to stay here holding,
this causes a little discomfort there, for the welder
stay all the time pressing here.
If your machine has "4T"
You will press and release,
Make your welder there, in time to stop, press again and loose.
I particularly
do not like these triggers with These clamps here
And many welders also do not like, is a little uncomfortable. Ok!
Here in this torch,
the handle of it is only one piece,
cast in one piece,
Here you have a trigger,
The cable goes inside here
You see, at any time the cable trigger will disturb.
Because it's only here to there,
Then you fits here,
and you have a torch
With a trigger, extremely comfortable
and one more thing,
if your machine is a machine that has opening of the arc by "Lift Arc"
and has no the control "4T"
You pull the trigger for welding, and has to keep it pressed,
If you release, the electric arc is stopped,
On this torch, even if your welding machine does not have this control (4T)
You'll pull the trigger,
pushes It here, and is ready
it lock, and the arc is open,
and you need not stay all the time, pressing the trigger.
To interrupt the welding
Are here welding,
just here to pull back
and is ready, loose, and it unlocks
and the arc is interrupted
In the technique "Walk the cup"
You will press, lock, and go making
go making the "walk the cup"
When it will be stopped, press
pull it back, and releases
and the arc is interrupted.
This is very important because you will continue to protect the end of the weld pool of contamination.
If your welding machine has up-slope,
the down-slope, Sorry..
The down slope will be there running, decreasing amperage
and you're still there, protecting the end of weld bead.
look here how comfortable it is
See here the size of the torch, the size of the handle
is a very comfortable size, and compatible with my hand, yeah
that greatly facilitate the life of welder
Have no doubt, when I show this torch for a welder.
and he takes it, uses and moves it
their eyes glow,
because they have a tool, which will be facilitating much of the work them, ok!
and here is the same thing,
You will can replace the short backcap
the medium backcap, according to its need there.
or by long Backcap.
then we have, short backcap, medium and long, ok!
Thank you for watching