Tip:
Highlight text to annotate it
X
this is the instrument This is the power plug
this is rated for 230 Volt. So please make sure
your power plug is 230 Volts. Connect the adaptor
in this point
and connect it to the power point
Now take
Now don't do anything on the screen
Take the wire
Pull one end
to the remote point where ever you require
and other end is your sensor. This you have to connect
at this terminal
you have to connect to the instrument. This is terminal 1
sensor 1
the lower one.The upper one
Don't use it. It is for another sensor
everything is already programmed you can just see by pressing this
just press escape
again press escape
now you can see this is sensor 1
and you can see your the temperature is twenty point four degree
it has started recording. you can see the recording
is happening over here.
if by mistake
if you are on sensor 2
you will not see anything over here. so just press the escape button so you will come
to
sensor number 1. The system is now
working there is nothing else to be done
now if you want to change any parameters
enter
this is for programming
system set up you will not need to do anything
you can see it is in English if you want to change the
centigrade to fahrenheit
press this button it will come here
press this button it will go to F. Press again it will
come to C. If you are okay with it press enter
the date is already programmed. if you want to change anything
press here. press up
press down. after each entry press enter
enter. enter.enter
everything will be lost
in this case I'll do yes and then press ENTER
so
that one is over. if you press escape the previous screeen
this is sensor. sorry
if you want to go any changes in sensor 1
just Press this one set up.Press enter
now the readings are being taken every ten minutes
so if you want to change
for example if you want to take every 5 minutes
just change it 5 minutes
press enter or if you want
like 1 hour press 1
so now it is taking every 1 hour 10 minutes
so for the time being I will leave it at 10
after each entry you have to press enter
this is the display graph. I will show you what is 50
and 1 means
this is 50 and this is 1. So you will see the graph if it is 20 degree you will
see graph some over here.If you want a better graph
you can change that like 10 to 30
so I am keeping it like that
so 50 and
1. and if you want an alarm
in this instrument come to alarm set up. press enter
right now is disabled press enable
press enter trigger alarm
for how many seconds for how many seconds you want to hear the
alarm so you can put for
10 seconds for example
press enter. here if the temperature goes above 6 degree for 5 minutes
or if the temperature goes below 2 degree
for 4 minutes, there will be an alarm
this you can change whatever you want. in this case above
6 degree for 5 minutes or below 2 degree for
four minutes then in that case
alarm will be activated.
there is a local alarm in this instrument there is a beep sound
so for the time being i'll set it
disabled. and from this screen you can press escape
it will go back. so now the programming is over
now it's already recording. It has already started recording but since we are recording
every 10 minutes
it is reading very slowly so I will just
show it for every
5 seconds
so that you can see the graph
enter. 5 seconds
now we an see a faster graph
are you sure? yes. now you can see a faster graph
first reading has come
second reading has come
third reading has come
now for zooming out this buttons you can zoom in
and out
you can see the
here you can see 4.30, 5 O'clock like that
here you can see a better zooing
now again every 10 minutes
it is going backwards and for moving left suppose you have a fulll line of graph
you can always move backwards or forward
you can see
backwards or forward for changing he date or time whatever you want to look at
That is all basically. so I will just change the
the sampling data to 10
minutes because otherwise memory will be full very fast
so I will make this
sampling data every 10 minutes
10 minutes
and seconds I put zero
so this takes the reading every 10 minutes and you can see the graph
on the screen
so every time it asks because previous data was for 5 seconds. Now we are changing
it. That is why it is asking
So now we will say yes. That is all it is
there is nothing much to do. It is already recording continuously