Tip:
Highlight text to annotate it
X
Hi everyone. I wanted to do a short video
of mounting a scope to rifle to show folks that it can be done it's pretty easy to do.
I wanted to keep it short so people could spend just a few minutes
and then go yeah I could probably do that before they spend the time
it takes to do the research and figure out all the steps and
may be particularly for a different rifle so
let's get started. What I have here is a Remington 700 chamber in 300 Win Mag.
The bolt's been removed and I checked for safety there's nothing in here
no round in the chamber so we're safe to go there. The first step that we want to do
is remove the plugs screws that
we're actually going to be mounting the brackets to so Rd got to the screws removed
this one in this one so I'll just takes forever
and quickly the other two
now should probably save these case you wanna take to
scope offer saw a rifle without the scope for something like that so you can
put
your pollsters and obviously they have a purpose to keep counting right now to
their
so posters up
go ahead take a little to read more on Q-two and
clean to the whole
right hear the bass is it going to be using
from leopold and therefore Remington 700 to make sure you get the right ones for
your rifle
I had a poor thing you know for the Remington 700 at least
is that it comes with a pair said launchers
said a short screws the short ones gonna front the long ones go on the rear
if you get those reversed your boat walk was properly
but it will close and it'll feel the fire one thing that
I was wondering where the instructions were for these and mounts
and there are two here there aren't any the front and white lace in the package
you can only tell it
but it does come open for trick me first
although there just a basic setup instructions that actually doesn't talk
about a long story short sure thing
I have the rear
base sitting on a rifle the links between
the screw holes is actually different so you can't confuse 'em
and the way this is configured this noches wear them out actually gonna be
so that service how that has to go or hanging off the back
front now I have a decision to make as a lying on the right for all set
I can either have the mousy here or
I can have see here
now I sort of dry fit my scope in place a little bit ago
to see where I would like it and I actually decided that I want
now to sit like this so I'm gonna go ahead and stir that place
alright I've got to the screws it and I'm gonna go ahead
the third wanna I'm going to use a little bit blue
thread lock for me here reporters
you don't have to but then they do say if you do
actuaries blue and not read Res
per minute I'm not planning on
removing this so the bases from the rifle so
that's another reason and it's a .300 Win Mag
so picture don't have anything back
clean up their alright
on the go ahead last screw
alright of course cruiser for a back remembering that the los tres doing
factual going from I've got my threadlocker on their
clean it up a little bit and these artwork down so hand fork
where I think they're supposed to be a you can buy a special
fancy torque wrench type deal and talk to standard specifications
if your gonna to a lot I suggest you do that but I did to now ready to move on
to the rents the Rings that I have ur
leopold KRW I
they can quickly be taken of us for
right for although I
don't anticipate needing that I think I got means more because they're on sale
at a location that I purchased them at
rather than it being like take them off the rifle quickly
already have the for already in place now I'm just going to
loosen the rearing both the rains are identical by the way so you don't have
to worry about which one goes where
saying that place and
tightening backup
so that's pretty much it the rains are in place
like as often I guess would be nice disease of any type
for rifle system with this rail system so if I did need a
take the scope of and swap it out or put it on a different life or
whatever it might be it would be pretty nice you could do it field for
starting to take the top of the ranks and Moscow
so I've got the rearing top have taken of it
work on the front one thing that's nice as they do include
this ranch so you don't have to fuss around finding the proper size research
want
so and
these taken off and
stopping place
now with my rents disassemble I'm gonna go ahead
my scope in place just said one thing I didn't say earlier was that
with the rings they'll come in low medium or high
and you'll hafta figure out for your particular riflescope combination what
you're gonna need
in my case its medium and a couple other things that you're looking for
is when you set a scope and
the ranks does the front scope clear the rifle Vera
and in the back are you still going to be able to work your ball properly
was lows on this weapon I'm not able to work the ball properly
so I want with me I mentioned earlier to that
I think I mentioned earlier that this was a revenge kept actually redfield
me models
so correction so now with that place
I'm not going to a lot there's a lot on the Internet you can look at
talks about how do you make sure that here
perfectly vertical horizontal on all that how to cite that in
but also about where your site goes
as far as when you're looking down
is how far it is from I am NOT going all that
there's video on the internet about and I'm not gonna die alone in today
I'm gonna put the top-of-the-range back on
and I wait or go to the range do the rest
alright
I have the front-running on and I love it back
I wanted to show you this process because after this nafta
rank over the to with the SCO that's a little
unsettling if you've never done it before are
I want to really well yours hater for something onto a
scope cost a couple box so I
he's down I'm not going to use thread lock
armies because I'm gonna just this later
once I get to stalin adjusted all the screws are tightened down
go ahead back out each juror individually
put Loctite or talk on gonna put it back in place
that way I don't compromise the adjustment made to the scope
by taking them all at once so just individually take
do that so that *** I have a some screws the time they are here
and I'll be finished or
that's it scopes all mounted on their I don't really know how long it took me
because I was
doing some laundry in answering couple emails and some other things while I was
in the process of doing this
corning but it didn't take that long so hopefully now
maybe have a little work office let's go by yourself and spin the time that it
takes to
do the research thanks for your particular right for your particular
said good
yeah
good