Tip:
Highlight text to annotate it
X
Building with Allan Block - Stairs
Whether built directly into the wall, in front of the wall or sweeping off to the side,
stairs are a great addition to almost any project.
When building stairs, choose your path wisely and find the most natural path to
maintain a comfortable rhythm to your stairway
You can break up long sets of steps with landings,
Add a turn and a landing to break up the stair line
or use switchbacks or serpentines to meander up the hill.
Tackle your slope by matching your stairway design to the natural grade of the slope
On steep slopes, keep the blocks tight together. With Allan Block you get an 8 inch rise and a 12 inch run
On gentle slopes, add pavers or other materials to increase the depth of the tread and length of the run
Landings are another way to soften a long stairway and are an easy way to tie sets of steps together.
Stairs can be designed with flowing curves or straight lines.
Curved sidewalls create a softer look.
Straight sidewalls and corners create a crisp look but will require more time to build.
Before you begin, you must first determine how many steps you will need.
Measure the total rise of your slope in inches and divide by eight.
Which is the height of the block.
Be sure to factor in any code requirements before you prep the site.
In this example we will show you how to build stairs into a wall using flowing curves.
Remember always begin building at the stair location and build out.
Excavate the Stairs
Once the number of steps has been determined, Excavate the stair location .
based on the rise and run in you approved plans
The minimum minimum width for a base trench is 24 inches.
The depth of the trench is determined by allowing for 6 inches of base material plus 1 inch per foot of wall height.
If organic or wet soils are still present in the base trench area they must be
removed and replaced with granular material
Excavate the base trench to the necessary depth.
Then compact and level the base trench making a minimum of 2 passes with a mechanical plate compactor
Place the drainpipe at the lowest possible point toward the back of the
trench that can be vented to daylight every 50 feet.
Now that the base trench is ready place a minimum of 6 inches of wall rock in the base trench and rake smooth.
compact the base making a minimum of 2 passes.
Install the Base Course
place the blocks toward the front of the trench allowing for a minimum of for 6 inches behind the blocks
Then fill in the area in front of the blocks with on-site soils.
This will keep the base course blocks from shifting while filling and compacting.
Fill the hollow cores, 12 inches behind the block and the stair location with wall rock.
backfill and compact
Compact behind the block in a path parallel to the wall, working from the back of the block
to the back of the backfill area.
Make a minimum of 2 passes with a mechanical plate compactor.
Always compact in 8 inch lifts or less.
Remember to keep all heavy equipment at least 3 feet away from the back of the blocks.
Remove any excess material from the top surface of the blocks by sweeping the block clean with a broom.
Use a level to screed the stair tread area then check for level from front to back
and side to side.
Making sure the stair tread is level with the top of the first course of blocks.
Install the Stair Riser
Measure the distance for the next stair riser and place the blocks, making sure to allow for 6 inches behind the blocks.
Measure the distance between the stairs to make sure that the blocks are parallel with the stairs in front.
Place a temporary block on top of the wall close enough so that you can place .
a 4 foot level from the block to the stair riser blocks.
This will ensure the stair riser blocks will be level with the rest of the wall.
Then level and adjust the rest of the stair riser blocks
To continue building your wall out form the stair location,
break the wings off the blocks by striking the back of the wing with hammer to obtain a clean break.
Then place the blocks tight together, following the layout on the approved
plans making adjustments as necessary.
You can place a small amount of wall rock under the blocks to level them
then check the blocks for level and make adjustments if necessary
Place a small amount of wall rock in front of the blocks for the stair riser
to keep them from shifting during compaction.
Fill the hollow cores , 12 inches behind the block and the next stair location
with wall rock. Then backfill any remaining area behind the wall rock with on-site soils.
Run the plate compactor over the top of the blocks where there are 2 or more courses
and behind the block where there is only one course.
Continue compacting the wall rock behind the wall as well as the excavated area of the next stair riser.
Screed the next stair tread area and check for level from front to back and side to side.
Continue Building
measure the tread area to make sure it is parallel and at the correct distance.
Place the next temporary block to level the stair riser. And check for level.
Continue building the wall out from the stair location.
Place some fill in front of the blocks
Fill the hollow cores and behind the blocks with wall rock Fill any remaining areas with on-site soils.
Then run the plate compactor over the top of the blocks where there are 2 or more courses and behind the block where there is only one course.
Continue compacting the wall rock behind the wall as well as the excavated area of the next stair riser.
Continue this process to the top of your wall.
Place the blocks for the next stair riser and measure for parallel and distance
Place a temporary block and adjust for level
Build the wall out from the stair location.
Add fill in front of the blocks
Fill the cores, behind the wall and the stair tread with wall rock.
Back fill any remaining areas and compact.
On the last course of the wall you can choose to fill the block cores
and the entire backfill area with plantable soils to finish off your wall.
In this example we have shown you how to build stairs into a wall.
You can also build stairs in front of a wall using curves, right angles or sweep them along the wall.
Or let your imagination run wild and create your own stair design.
You can finish your stair treads with one of these options,
AB Capstones,
AB Capstones and Pavers,
Pavers or Concrete.
Choose the style that best compliments your landscape
To enhance your project view the other Building Options or visit us at allanblock.com