Tip:
Highlight text to annotate it
X
Let me give you a quick introduction to the Q-Sys Designer Software. 让我为你做一个 Q-Sys系统设计软件的简要介绍
It's broken up into three major sections: 这个软件分成3个主要部分
the Left-Side Pane is where you'll find most of the physical inventory pieces like amps and loudspeakers, 左边的这个控制面板里, 你可以找到所有物理组件,如功放和扬声器
User Control Interfaces, and a few other options. 用户控制界面和一些其他的选项
the Right-Side Pane has all of the DSP Components like mixers, equalizers, delays, audio players, that kind of stuff. 右边这个控制面板是关于DSP组件, 如混音器,均衡器,延时器,音频播放器等诸如此类的东西
And the center is called the Schematic. 中间是设计区
This is where you'll build your design. 这是你用来构建你的设计的地方。
Speaking of which, let's build a real simple design, shall we? 说到这个软件,不如然我们来 组建一个简单的系统设计,如何?
First of all, you'll need to set up the parameters of your Core. 首先,你需要设置你的Core处理主机的各项参数,
For your Core you can give it a name and location, 你要给你的主机起个名字并定义它的位置
choose the model, 选择型号
and assign any I/O Cards that you might have installed in the Core. 然后设定所有的安装在 Core主机上的输入/输出卡
Next you come over here to the Inventory panel and add the physical and virtual inventory to your design, 接下来,在设备库控制面板中 添加物理和虚拟设备到你的设计中
including your amplifiers and loudspeakers, as well as any peripherals you might have like a Page Station or Touchscreen. 包括功放和扬声器, 也包括任意的附件,如呼叫站或者触摸屏等
So lets add an amplifier and a couple loudspeakers to our design. 我们将一台功放和一对扬声器 添加到系统中
Next you need to drag these components into your Schematic. 接下来你需要将这些组件 拖拽到你的设计区中
Let's start with our Mic-Line input, 我们从话筒线路输入开始
next let's throw in a mixer, 然后是将混音器,
a parametric equalizer, 一个参量均衡器
and maybe some delay into our design. 或者还有一些延时器到我们的设计中
There are a few ways to wire your design, 这里有几种方式为系统连线方式
but the easiest is to just physically drag your mouse from one to the other to wire the components together. 但是最简单的一种是用你的鼠标将物理设备从一个拖到另外一个, 这样就将这些组件连接在一起了
Again, if you want to adjust any parameters of each component, 如果你想调整 任一组件的参数设置
let's say to increase the band of the parametric equalizer from four to ten, 比如说把参量均衡器的频段 从4增加到10
just click on the component 只要点击这个组件
and change it in the control Properties. 就可以在控制属性里修改参数。
Once you're happy with that, 调节到你觉得合适的数值后
all you need to do is send your audio to your output card, 你所需要做的只是将音频信号 发送到音频输出卡上
then to your amplifier and then to your speaker. 然后到你的功放,最后是扬声器中。
So just drag these components into your Schematic, 因此只要拖拽这些组件到你的设计区中,
and wire them up. 然后将它们连接起来,
And there you have it, 这样你就完成了。
you're ready to load this design to the Core and start passing audio. 现在你可以将这个设计上传到Core主机中并开始传送音频了。