Tip:
Highlight text to annotate it
X
So folks, here I am again, the Paddy of Airsofttipps. Today with my review about the EF 6-35 PDW, GBB from GHK.
My source was the shop Sniper As. The cost item there is 239,00 €.
Let’s start with the review.
The whole thing is packed in such a simple carton.
Only the sticker here on the top shows us, what is inside this carton.
The delivery consists of a simple operating construction, written in English, German, French and Spain.
A speed loader with an adapter for the enclosed magazine.
And last but not least: the weapon itself.
Specs.
Let’s start with the measurements.
The weapon has got a length of 715mm with pulled out stock and a length of 485mm with pulled in stock and has got a weight of 2,2kg.
The enclosed Magazine clasped 40 shots. The energy is given with 1,5 joule. But we will just check that.
To show you the workmanship, I expanded the picture, I hope it doesn’t disturb you.
We start right at the front with the flash hider. It is very nice manufactured.
Here, we have got the outer barrel, too, which has got the usual ‘Elite force pattern’.
Than we have here this whole thing made from metal, which normally portrayed the removal of gas.
We have got the whole upper receiver, which is completely milled out of one part of metal.
This one is very sturdy and if you look at it you won’t find any production markings. The whole thing is very clean worked.
I find it absolutely nice and it has got the feeling to be very sturdy.
Also the only detail made from plastic has got no markings because of production. Everything is very well and clean worked.
Also the stock is very nice, tough and sturdy. It only wobbles minimally.
The only thing which wobbles is this specification to fix the stock on the body. But you will be able to fix it if you want to. After it, it won’t wobble anymore.
The ending of the stock is also very nice. The rubber is reasonable and strong. So you mustn’t worry that the rubber will fall off.
To show you the markings, I expanded the picture again.
We have got the ‘UMAREX’ logo because they imported it.
Than we’ve got a simple serial number.
The ‘6mm BB’ and naturally the ‘F’, which isn’t engraved but printed on
The different positions of the fire selector lever are also nice worked and engraved. The paint has been set in, so that there won’t be signs of wear after a short time.
On the left side of the body, above the magazine, you find the ‘elite Force’ logo and underneath the term of the weapon itself.
The inner workmanship:
Here once the bolt, as soon as the other assemblies.
The bolt carrier is also made from metal. Just the same of the inner parts are made of sturdy plastic. Also very reasonable and clean worked.
The whole thing will be taken forward with this spring and this pole.
Everything is very clean and sturdy worked. Only the lacquer is a bit slim, but it isn’t a problem with this inner parts. The whole thing is very good greased till the producing.
Let’s move to the reviver
You just see the innards of the reviver
The whole thing is very sturdy and strong manufactured. Most parts are made of metal. Because of that, the whole can also score in the areas of quality and lifespan.
Let’s start with the most important things.
You are able to use the safety on both sides of the weapon. Means: you find it on the right and on the left side.
To make the weapon ready to fire, you have to insert the magazine into the weapon until it stacked.
After it, you have to clasp the T-grip and pulled it back. Let it fast forwards and the weapon is loaded.
If your magazine is empty after the 40 shots, the bolt will stop in the rearmost position and you can take the magazine away.
After it, you can insert a new magazine and the whole thing will be ready to fire again, after pushing this button.
Now the weapon is again ready to fire.
The weapon will be delivered with such a flip-up sight.
The back sight is fixed on such a raised mount.
These mount is fully adjustable. The back sight is adjustable to the right and the left side.
The front sight is adjustable in its height
You are able to remove the flash hider completely to install, for example, a silencer or tracer.
The whole barrel- unit, including the Hop-up, is removable. I won’t show it. One moment please.
Pull the magazine out.
By removing these two Allan-key screws. After it, you are able to remove the whole system.
To load the magazine, you can use the speed loader but you need much strength and I’ve got the feeling that the speed loader doesn’t tolerate it.
I wouldn’t take it into the field. Outside, you can use it, but inside I wouldn’t rely on it.
There are other solutions to work with these magazines without problems.
Otherwise, you can load it manually, like I did it.
Then we only have to fill the magazine with gas. You have to do it here on the back of the magazine.
We raise the gas bottle and now we are ready. And we can change to the shooting test.
Before, I want to show you, how to disassemble the weapon for cleaning.
You only have to get the bolt and the spring. It’s easy.
Once we push the pin out. I’ll do it with some tools because the pin is very strong in the beginning. But that’s right. One moment please.
The pin is designed to didn’t be fully removable. Means: it can’t get lost. That’s very practical.
As soon as the pin is pulled out, you can open the upper receiver and you are able to remove the bolt and the spring with the reload lever.
The whole thing is one assembly.
Then we have got the bolt. You can also disassemble the bolt.
We only remove the spring and then we’ve got the bolt. It jumped out immediately. You have to be careful.
Now we have got the bolt, the spring, the pole and the conclusion of it, which will get into the reload lever later.
To reassemble the weapon, we firstly take the spring and grab it back onto the pole.
The same with the conclusion. You have to be careful because it likes to split up.
The whole thing together
Now the part, which is a bit tricky.
We take the reload lever, lead it through and hook it in there. Now, the pole stuck out.
Oh, the rubber removed. I probably removed it.
After it, you are able to insert the assembly completely. Let the whole thing hook in and you can close the body. And you can push the pin back by hand.
About the result: the result is very positive
The weapon is very sturdy worked. The whole body it out of order. It is very cool!
I had much fun to work with it.
Also the innards are super worked. I really had much fun.
For 239€ you’ve got a super GBB in the average price segment.
Namely: 239€ isn’t much for a GBB.
In this instance absolutely justified. I would pay more money for it.
Workmanship on the outside and on the inside top!
Magazine: super worked. Only the GHK- magazines fit wit it but that’s also not weird.
I can only highly recommend it.